| Author |
Message |
danbohlen
User
Joined: 18 Aug 2008
Posts: 677
Location: Evendale OH
|
 Posted: Tue Jul 01, 2008 7:36 am |
 |
|
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
Post generated using Mail2Forum (http://www.mail2forum.com)
_________________
Dan Bohlen
Senior Staff Engineer
GE Aircraft Engines |
|
| Back to top |
|
 |
Gallagher, Keith J.
Guest
|
| Posted: Tue Jul 01, 2008 7:38 am |
|
|
Have you tried?
/nopr (before reading in the presures)
And
/gopr (Reset to normal)
Keith Gallagher
Lead Engineer/ Project Manager
Belcan Corporation
Advanced Engineering & Technology Division
513-985-7443 (Tel)
513-985-7238 (Fax)
--email address suppressed-- (email)
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 10:36 AM
To: ANSYS User Discussion List
Subject: [Xansys] Turning off useless error messages
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
This e-mail transmission contains information that is confidential and may be
privileged. It is intended only for the addressee(s) named above. If you receive
this e-mail in error, please do not read, copy or disseminate it in any manner.
If you are not the intended recipient, any disclosure, copying, distribution or
use of the contents of this information is prohibited. Please reply to the
message immediately by informing the sender that the message was misdirected.
After replying, please erase it from your computer system. Your assistance in
correcting this error is appreciated.
Post generated using Mail2Forum (http://www.mail2forum.com) |
|
| Back to top |
|
|
danbohlen
User
Joined: 18 Aug 2008
Posts: 677
Location: Evendale OH
|
| Posted: Tue Jul 01, 2008 7:39 am |
|
|
Oh BTW, I think this has been discussed recently, but the archive is
down. I got this upon my search.....
Lurker - failed to render page:
Cannot open database snapshot (Permission denied):
The configured database 'dbdir' in the config file could not
be opened. Typically this means that it is not readable by the user
which the cgi is invoked as. We suggest making dbdir and all files in it
readable by everyone since you are serving them on a website anyways.
Dan Bohlen
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
Disclaimer - Preliminary Data
The preliminary data contained herein may be incomplete or subject to
change and is based upon assumptions that may not have been verified or
may not reflect actual operating conditions. This data is presented for
discussion purposes only and is not intended to be, nor should be used
for any other purpose or in any other context.
GE proprietary
The information contained in this document is GE proprietary information
and is disclosed in confidence. It is the property of GE and shall not
be used, disclosed to others or reproduced without express written
consent of GE, including, but not without limitation, it is not to be
used in the creation, manufacture, development, or derivation of any
repairs, modifications, spare parts, designs, or configuration changes
or to obtain FAA or any other government or regulatory approval to do
so. If consent is given for reproduction in whole or in part, this
notice and the notice set forth on each page of this document shall
appear in any such reproduction in whole or in part. The information
contained in this document may also be controlled by the U.S. export
control laws. Unauthorized export or re-export is prohibited.
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 10:36 AM
To: ANSYS User Discussion List
Subject: [Xansys] Turning off useless error messages
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
Post generated using Mail2Forum (http://www.mail2forum.com)
_________________
Dan Bohlen
Senior Staff Engineer
GE Aircraft Engines |
|
| Back to top |
|
|
eric.miller
User
Joined: 15 Aug 2008
Posts: 906
Location: Tempe, AZ
|
| Posted: Tue Jul 01, 2008 7:49 am |
|
|
Ouch. It works for me, but I probably have permission... Jason and I
will check it out.
Eric
------------------------------------------------------------------------
---
Eric Miller
Principal
Director, Analysis &
Design Technologies
Phoenix Analysis & Design Technologies
www.padtinc.com
(480) 813-4884 x103
--email address suppressed--
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 7:39 AM
To: ANSYS User Discussion List
Subject: Re: [Xansys] Turning off useless error messages
Oh BTW, I think this has been discussed recently, but the archive is
down. I got this upon my search.....
Lurker - failed to render page:
Cannot open database snapshot (Permission denied):
The configured database 'dbdir' in the config file could not
be opened. Typically this means that it is not readable by the user
which the cgi is invoked as. We suggest making dbdir and all files in it
readable by everyone since you are serving them on a website anyways.
Dan Bohlen
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
Disclaimer - Preliminary Data
The preliminary data contained herein may be incomplete or subject to
change and is based upon assumptions that may not have been verified or
may not reflect actual operating conditions. This data is presented for
discussion purposes only and is not intended to be, nor should be used
for any other purpose or in any other context.
GE proprietary
The information contained in this document is GE proprietary information
and is disclosed in confidence. It is the property of GE and shall not
be used, disclosed to others or reproduced without express written
consent of GE, including, but not without limitation, it is not to be
used in the creation, manufacture, development, or derivation of any
repairs, modifications, spare parts, designs, or configuration changes
or to obtain FAA or any other government or regulatory approval to do
so. If consent is given for reproduction in whole or in part, this
notice and the notice set forth on each page of this document shall
appear in any such reproduction in whole or in part. The information
contained in this document may also be controlled by the U.S. export
control laws. Unauthorized export or re-export is prohibited.
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 10:36 AM
To: ANSYS User Discussion List
Subject: [Xansys] Turning off useless error messages
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
Post generated using Mail2Forum (http://www.mail2forum.com)
_________________
Eric Miller
Principal
Director, Analysis &
Design Technologies
Phoenix Analysis & Design Technologies
www.padtinc.com |
|
| Back to top |
|
|
danbohlen
User
Joined: 18 Aug 2008
Posts: 677
Location: Evendale OH
|
| Posted: Tue Jul 01, 2008 7:56 am |
|
|
Tried, but doesn't help on error/warning messages.
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Gallagher, Keith J.
Sent: Tuesday, July 01, 2008 10:39 AM
To: ANSYS User Discussion List
Subject: Re: [Xansys] Turning off useless error messages
Have you tried?
/nopr (before reading in the presures)
And
/gopr (Reset to normal)
Keith Gallagher
Lead Engineer/ Project Manager
Belcan Corporation
Advanced Engineering & Technology Division
513-985-7443 (Tel)
513-985-7238 (Fax)
--email address suppressed-- (email)
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 10:36 AM
To: ANSYS User Discussion List
Subject: [Xansys] Turning off useless error messages
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
This e-mail transmission contains information that is confidential and
may be privileged. It is intended only for the addressee(s) named above.
If you receive this e-mail in error, please do not read, copy or
disseminate it in any manner.
If you are not the intended recipient, any disclosure, copying,
distribution or use of the contents of this information is prohibited.
Please reply to the message immediately by informing the sender that the
message was misdirected.
After replying, please erase it from your computer system. Your
assistance in correcting this error is appreciated.
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
Post generated using Mail2Forum (http://www.mail2forum.com)
_________________
Dan Bohlen
Senior Staff Engineer
GE Aircraft Engines |
|
| Back to top |
|
|
David S Stapp
Guest
|
| Posted: Tue Jul 01, 2008 8:00 am |
|
|
Dan,
I usually just do a /nopr at the beginning and /gopr at the end of any input
file for which I don't care about the warning messages.
David Stapp
Peregrine Consulting, Inc.
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On Behalf
Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 10:36 AM
To: ANSYS User Discussion List
Subject: [Xansys] Turning off useless error messages
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
Post generated using Mail2Forum (http://www.mail2forum.com) |
|
| Back to top |
|
|
Gallagher, Keith J.
Guest
|
| Posted: Tue Jul 01, 2008 8:02 am |
|
|
I have this as an undocumented feature:
/NERR,,,-1 - This command will allow you to ignore all error messages
Cant swear if it actually works. Maybe you can share if it does.
Keith Gallagher
Lead Engineer/ Project Manager
Belcan Corporation
Advanced Engineering & Technology Division
513-985-7443 (Tel)
513-985-7238 (Fax)
--email address suppressed-- (email)
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 10:57 AM
To: ANSYS User Discussion List
Subject: Re: [Xansys] Turning off useless error messages
Tried, but doesn't help on error/warning messages.
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Gallagher, Keith J.
Sent: Tuesday, July 01, 2008 10:39 AM
To: ANSYS User Discussion List
Subject: Re: [Xansys] Turning off useless error messages
Have you tried?
/nopr (before reading in the presures)
And
/gopr (Reset to normal)
Keith Gallagher
Lead Engineer/ Project Manager
Belcan Corporation
Advanced Engineering & Technology Division
513-985-7443 (Tel)
513-985-7238 (Fax)
--email address suppressed-- (email)
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 10:36 AM
To: ANSYS User Discussion List
Subject: [Xansys] Turning off useless error messages
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
This e-mail transmission contains information that is confidential and
may be privileged. It is intended only for the addressee(s) named above.
If you receive this e-mail in error, please do not read, copy or
disseminate it in any manner.
If you are not the intended recipient, any disclosure, copying,
distribution or use of the contents of this information is prohibited.
Please reply to the message immediately by informing the sender that the
message was misdirected.
After replying, please erase it from your computer system. Your
assistance in correcting this error is appreciated.
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
Post generated using Mail2Forum (http://www.mail2forum.com) |
|
| Back to top |
|
|
danbohlen
User
Joined: 18 Aug 2008
Posts: 677
Location: Evendale OH
|
| Posted: Tue Jul 01, 2008 8:03 am |
|
|
Thanks, guys. I got it working now.
I used a combo of
/uis,msgpop
/nopr
And
/NERR,,,-2
To do the trick.
Dan
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 10:57 AM
To: ANSYS User Discussion List
Subject: Re: [Xansys] Turning off useless error messages
Tried, but doesn't help on error/warning messages.
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Gallagher, Keith J.
Sent: Tuesday, July 01, 2008 10:39 AM
To: ANSYS User Discussion List
Subject: Re: [Xansys] Turning off useless error messages
Have you tried?
/nopr (before reading in the presures)
And
/gopr (Reset to normal)
Keith Gallagher
Lead Engineer/ Project Manager
Belcan Corporation
Advanced Engineering & Technology Division
513-985-7443 (Tel)
513-985-7238 (Fax)
--email address suppressed-- (email)
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 10:36 AM
To: ANSYS User Discussion List
Subject: [Xansys] Turning off useless error messages
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
This e-mail transmission contains information that is confidential and
may be privileged. It is intended only for the addressee(s) named above.
If you receive this e-mail in error, please do not read, copy or
disseminate it in any manner.
If you are not the intended recipient, any disclosure, copying,
distribution or use of the contents of this information is prohibited.
Please reply to the message immediately by informing the sender that the
message was misdirected.
After replying, please erase it from your computer system. Your
assistance in correcting this error is appreciated.
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
Post generated using Mail2Forum (http://www.mail2forum.com)
_________________
Dan Bohlen
Senior Staff Engineer
GE Aircraft Engines |
|
| Back to top |
|
|
Thompson Diraviam, Joe...
Guest
|
| Posted: Tue Jul 01, 2008 8:04 am |
|
|
Hi Dan,
You can try this and see
/nerr,-1,,,,100000
Thanks,
Joel
TCS America
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 10:36 AM
To: ANSYS User Discussion List
Subject: [Xansys] Turning off useless error messages
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
Post generated using Mail2Forum (http://www.mail2forum.com) |
|
| Back to top |
|
|
eric.miller
User
Joined: 15 Aug 2008
Posts: 906
Location: Tempe, AZ
|
| Posted: Tue Jul 01, 2008 8:31 am |
|
|
Dan,
Shocked that /nerr doesn't work.
What I do is /out to a junk file.
Eric
------------------------------------------------------------------------
---
Eric Miller
Principal
Director, Analysis &
Design Technologies
Phoenix Analysis & Design Technologies
www.padtinc.com
(480) 813-4884 x103
--email address suppressed--
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 7:36 AM
To: ANSYS User Discussion List
Subject: [Xansys] Turning off useless error messages
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
Post generated using Mail2Forum (http://www.mail2forum.com)
_________________
Eric Miller
Principal
Director, Analysis &
Design Technologies
Phoenix Analysis & Design Technologies
www.padtinc.com |
|
| Back to top |
|
|
danbohlen
User
Joined: 18 Aug 2008
Posts: 677
Location: Evendale OH
|
| Posted: Tue Jul 01, 2008 8:44 am |
|
|
Eric,
It seems to now - I thought it'll stop the pop up windows during and
interactive run, but I needed to do the /UIS as well.
Dan
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Eric Miller
Sent: Tuesday, July 01, 2008 11:31 AM
To: ANSYS User Discussion List
Subject: Re: [Xansys] Turning off useless error messages
Dan,
Shocked that /nerr doesn't work.
What I do is /out to a junk file.
Eric
------------------------------------------------------------------------
---
Eric Miller
Principal
Director, Analysis &
Design Technologies
Phoenix Analysis & Design Technologies
www.padtinc.com
(480) 813-4884 x103
--email address suppressed--
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 7:36 AM
To: ANSYS User Discussion List
Subject: [Xansys] Turning off useless error messages
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
Post generated using Mail2Forum (http://www.mail2forum.com)
_________________
Dan Bohlen
Senior Staff Engineer
GE Aircraft Engines |
|
| Back to top |
|
|
Matt Sutton
Guest
|
| Posted: Tue Jul 01, 2008 9:16 am |
|
|
This is one of those areas where I wish ANSYS would tag each warning
message type with a numeric value. Then, if they would create an APDL
command that allows you to specifically suppress\unsuppress a particular
warning message by its type id, you would get the best of both worlds.
You only end up suppressing the warnings you know are innocuous.
Matt Sutton
www.padtinc.com
-----Original Message-----
From: --email address suppressed-- [mailto:--email address suppressed--] On
Behalf Of Bohlen, Dan (GE Infra, Aviation, US)
Sent: Tuesday, July 01, 2008 7:36 AM
To: ANSYS User Discussion List
Subject: [Xansys] Turning off useless error messages
Hi All,
I have a set long input file that applies pressures to a model. I've
altered the model to where some of the element no longer exist. When I
read in the input files a get a ton of warning messages
*** WARNING *** SUPPRESSED MESSAGE CP = 40.703 TIME= 10:33:01
No defined or selected elements have pressure face with
NODES= 23572 23573 0 0. Specification not stored.
I'd like to unclutter my output and error files and not have these show
up anymore.
I used to be able to do this with
/NERR,,,-2
and I tried
/nerr,,,,,0
Any suggestions?
Dan Bohlen
RPC Military Stress Analysis
Senior Engineer
GE Aircraft Engines
1 Neumann Way, Evendale, OH
M/D E22 513-243-4645
Dial Comm 8-332-4645
^--------------------------------------------------------
| XANSYS - www.xansys.org |
| The Discussion List for users of ANSYS, Inc. Software |
| Hosted by PADT - www.padtinc.com |
^--------------------------------------------------------
Post generated using Mail2Forum (http://www.mail2forum.com) |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum
|
|
SmartFeed
